General

This coating work method is indicative and deals with the coating of a gypsum board floor with the ELAPROOF+SAND system. The ELAPROOF+SAND floor covering system consists of ELAPROOF PRIMER primer, ELAPROOF+SAND floor covering and ELACOAT TOPCOAT RAL / ELACOAT TOPCOAT topcoat.

The coating work method is not a repair plan or a construction plan. The overall design of the coating is always the responsibility of the site-specific designer.

Platform refurbishment

In areas to be renovated, all possible moisture-sensitive adhesive residues must be removed from the gypsum board floor. Any loose floor screeds must also be removed in their entirety.

Any gaps between the boards, screw holes and cracks in the board surfaces must be filled / levelled with a floor level suitable for gypsum board surfaces. A floor level suitable for chipboard surfaces should also be used for possible over-levelling. When using screeds, also check with the floor screed manufacturer for a suitable primer.

Primer

Prior to coating, cleaned and repaired gypsum board substrates are primed with ELAPROOF PRIMER without the addition of water. Allow the primer to dry completely before applying ELAPROOF + SAND. The purpose of the primer is to seal the surface of the chipboard from the moisture released by the incoming coating.

Sealing

If necessary, all structural joints and boundary points such as floor and wall joints, bushings, columns and seals of any floor wells, etc. are implemented with a combination of ELAPROOF INDOOR + ELAPROOF BASE FABRIC.

ELAPROOF INDOOR must be mixed before starting the seals. Use a whisk in the mixer that does not take air into the sealant when mixing, eg COLLOMIX KR series mixing paddle.

Apply ELAPROOF INDOOR sealant with a brush and press ELAPROOF BASE FABRIC onto the fresh compound so that all air escapes under the support fabric. Apply another coat of ELAPROOF INDOOR.

Sealing of one running meter (1 rmt) requires approx. 0.15 l of ELAPROOF INDOOR.

If the sealable bushings allow the pre-formed bushing to be threaded over the bushing into a collar, the bushings can be shaped, if necessary, for example, by cutting from N1 or N2 category geo-textiles, unless the ELAPROOF BASE FABRIC is wide enough to carry the penetration. ELAPROOF ROOF series reinforcement fabrics, available in widths of 150 mm, 350 mm and 1000 mm, can also be used for seals.

Coating

Before starting the coating, the ELAPROOF+SAND floor covering must be mixed. Use a mixing paddle in the mixer that does not take air into the sealant when mixing, eg COLLOMIX KR series mixing paddle.

The primed substrate is coated with ELAPROOF+SAND (M1 / EC 1) floor coating. The coating is applied to the substrate with a steel spatula.

ELAPROOF+SAND floor covering is applied to the substrate in two separate applications. The consumption of each application must be at least approx. 2.0 kg / m², in which case the total consumption is approx. 4.0 kg / m². The actual dry film thickness must be min. 2.0 mm.

The drying time between coats of ELAPROOF+SAND depends largely on the conditions at the installation site. At conditions of approx. + 20 °C, 50% RH can be applied a second time approx. 5 h after the first application. Lower temperatures and higher humidity significantly extend the drying time.

The ELAPROOF+SAND floor covering applied twice can be applied after approx. 12 hours in conditions + 20 °C, 50 % RH.

Topcoat

The dried ELAPROOF coating is treated with clear ELACOAT TOPCOAT or tinted ELACOAT TOPCOAT RAL topcoats to facilitate cleaning and maintenance. For monochromatic floors, we recommend topcoating with tinted ELACOAT TOPCOAT RAL topcoat to even out any colour differences in the ELAPROOF+SAND coating. On flaked floors, we recommend flaking with ELAPROOF Art&Deco Colour Chips on wet ELACOAT TOPCOAT RAL topcoat and, after drying, finishing with clear ELACOAT TOPCOAT topcoat.

In the topcoat, the topcoat component A is first mixed for 1 to 2 minutes, then the hardener component B is added to the mixed A component and mixed again for 2-3 minutes. Use, for example, the COLLOMIX KR series mixing paddle for mixing.

The mixture is applied on top of the dried ELAPROOF coating with a short-pile roller (6 – 7 mm) by cross-rolling. The consumption of the topcoat is approx. 110 – 200 g / m² / application, depending on the degree of roughness of the selected ELAPROOF+SAND coating. The topcoat is dry to dry after approx. 16 h at + 20 °C, 50% RH. The full duration of mechanical stress is achieved under the above conditions in about 4 days and the full chemical duration in about 7 days.

NOTE! Some shades of ELACOAT TOPCOAT RAL topcoats may require 2 to 3 coats to achieve sufficient coverage! See a separate table for the coverage of ELACOAT TOPCOAT RAL topcoats.

Structural drawings

All structural drawings related to ElaProof products in DWG and PDF format from the ProdLib-service.

Build Care Oy owns all rights to this coating work method. Designers are free to use this coating work method when creating repair and coating plans!

ALWAYS READ THE PRODUCT DESCRIPTIONS FOR THE PRODUCTS PRESENTED IN THE COATING WORK METHOD BEFORE STARTING THE INSTALLATION!

Updated: 12/2021 | JKo

General

This coating work method is indicative and deals with the coating of a concreate floor with the ELAPROOF+SAND system. The ELAPROOF+SAND floor covering system consists of ELAPROOF PRIMER primer, ELAPROOF+SAND floor covering and ELACOAT TOPCOAT RAL / ELACOAT TOPCOAT topcoat

The coating work method is not a repair plan or a construction plan. The overall design of the coating is always the responsibility of the site-specific designer.

Platform refurbishment

Adequate tensile and compressive strength is a key factor in the performance of coating materials. The concrete or screed substrate must be durable and have sufficient compressive strength.
The tensile strength of the substrate material is checked in accordance with EN 1542, and the tensile strength must be> 1.5 N / mm² (1.5 MPa).
The compressive strength shall be checked in accordance with EN 12504-2, and the compressive strength shall be> 25 N / mm² (25 MPa).
The substrate must be clean, sufficiently dry, and free of all contaminants such as dirt, oil, grease, weak coatings, and surface treatments.
If necessary, the weak layers are removed by sufficiently efficient mechanical methods such as grinding, milling, or blasting. In terms of coating, the best result is achieved if it is applied to a clean concrete surface with a roughness equivalent to a wood-ground concrete surface.

After cleaning, any cracks in the concrete floor are injected with injection resin meeting the EN 1504-5 standard, eg. HYDROPOX EP1.

Platform patching and levelling

Any cavities in the concrete surface are filled with a filling compound suitable for the coating combination before coating. If the concrete substrate to be coated has rough or uneven areas, they must be leveled with a leveling compound suitable for the coating combination. It should be noted that the irregularities tend to be visible on the coated surface.

Only special products that meet the above compressive and tensile strength requirements may be used to repair, straighten, and level the substrate. The suitability of the above products as a substrate for a liquid coating must always be ensured. from the product supplier.

Primer

Prior to coating, cleaned and repaired concreate substrates are primed with ELAPROOF PRIMER without the addition of water. Allow the primer to dry completely before applying ELAPROOF + SAND. The purpose of the primer is to seal the surface of the chipboard from the moisture released by the incoming coating.

Sealing

If necessary, all structural joints and boundary points such as floor and wall joints, bushings, columns and seals of any floor wells, etc. are implemented with a combination of ELAPROOF INDOOR + ELAPROOF BASE FABRIC.

ELAPROOF INDOOR must be mixed before starting the seals. Use a whisk in the mixer that does not take air into the sealant when mixing, eg COLLOMIX KR series mixing paddle.

Apply ELAPROOF INDOOR sealant with a brush and press ELAPROOF BASE FABRIC onto the fresh compound so that all air escapes under the support fabric. Apply another coat of ELAPROOF INDOOR.

Sealing of one running meter (1 rmt) requires approx. 0.15 l of ELAPROOF INDOOR.

If the sealable bushings allow the pre-formed bushing to be threaded over the bushing into a collar, the bushings can be shaped, if necessary, for example, by cutting from N1 or N2 category geo-textiles, unless the ELAPROOF BASE FABRIC is wide enough to carry the penetration. ELAPROOF ROOF series reinforcement fabrics, available in widths of 150 mm, 350 mm and 1000 mm, can also be used for seals.

Possible connections to the floor drain are also made by cutting the floor drain grommet from N1 or N2 class geo-textile or by cutting the reinforcement fabric of the ELAPROOF ROOF series. The bushing is installed using or ELAPROOF INDOOR compound. Apply ELAPROOF INDOOR sealant with a brush and press the grommet onto the fresh compound so that all air escapes under the backing fabric. Apply another coat of ELAPROOF INDOOR. When the bushing has dried, cut a hole of a suitable size for the bushing and press the floor drain clamping ring into place before starting the ELAPROOF+SAND floor covering.

Coating

Before starting the coating, the ELAPROOF+SAND floor covering must be mixed. Use a mixing paddle in the mixer that does not take air into the sealant when mixing, eg COLLOMIX KR series mixing paddle.

The primed substrate is coated with ELAPROOF+SAND (M1 / EC 1) floor coating. The coating is applied to the substrate with a steel spatula.

ELAPROOF+SAND floor covering is applied to the substrate in two separate applications. The consumption of each application must be at least approx. 2.0 kg / m², in which case the total consumption is approx. 4.0 kg / m². The actual dry film thickness must be min. 2.0 mm.
The drying time between coats of ELAPROOF+SAND depends largely on the conditions at the installation site. At conditions of approx. + 20 °C, 50% RH can be applied a second time approx. 5 h after the first application. Lower temperatures and higher humidity significantly extend the drying time.

The ELAPROOF+SAND floor covering applied twice can be applied after approx. 12 hours in conditions + 20 °C, 50 % RH.

Topcoat

The dried ELAPROOF coating is treated with clear ELAPROOF TOPCOAT or tinted ELACOAT TOPCOAT RAL topcoats to facilitate cleaning and maintenance. For monochromatic floors, we recommend topcoating with tinted ELACOAT TOPCOAT RAL topcoat to even out any color differences in the ELAPROOF + SAND coating. On flaked floors, we recommend flaking with ELAPROOF Art&Deco Colour Chips on wet ELACOAT TOPCOAT RAL topcoat and, after drying, finishing with clear ELACOAT TOPCOAT topcoat.

In the topcoat, the topcoat component A is first mixed for 1 to 2 minutes, then the hardener component B is added to the mixed A component and mixed again for 2-3 minutes. Use, for example, the COLLOMIX KR series mixing paddle for mixing.

The mixture is applied on top of the dried ELAPROOF coating with a short-pile roller (6 – 7 mm) by cross-rolling. The consumption of the topcoat is approx. 110 – 200 g / m² / application, depending on the degree of roughness of the selected ELAPROOF + SAND coating. The topcoat is dry to dry after approx. 16 h at + 20 °C, 50% RH. The full duration of mechanical stress is achieved under the above conditions in about 4 days and the full chemical duration in about 7 days.

NOTE! Some shades of ELACOAT TOPCOAT RAL topcoats may require 2 to 3 coats to achieve sufficient coverage!

Structural drawings

All structural drawings related to ElaProof products in DWG and PDF format from the ProdLib-service.

Build Care Oy owns all rights to this coating work method. Designers are free to use this coating work method when creating repair and coating plans!

ALWAYS READ THE PRODUCT DESCRIPTIONS FOR THE PRODUCTS PRESENTED IN THE COATING WORK METHOD BEFORE STARTING THE INSTALLATION!

Updated: 12/2021 | JKo

General

This coating work method is indicative and deals with the coating of a tiled bathroom floor with the ELAPROOF+SAND system. The ELAPROOF+SAND floor covering system consists of ELAPROOF PRIMER primer, ELAPROOF+SAND floor covering and ELACOAT TOPCOAT RAL / ELACOAT TOPCOAT topcoat

The coating work method is not a repair plan or a construction plan. The overall design of the coating is always the responsibility of the site-specific designer.

Platform refurbishment

The tiled floor in the bathroom must be waterproofed with approved waterproofing for use under the ceramic tiles. This waterproofing must not be more than 10 years old during the coating phase, based on Finnish RIL 107-2012 guideline. Please check if there are any similar restrictions in the local regulations and follow those?

The tile surfaces are washed first with an acidic (pH 1 – 3) detergent for cleaning the tile surfaces and then with an alkaline (pH 8 – 11) detergent and rinsed with plenty of water. The cleaned floor is allowed to dry for at least 1 day before starting the coating.

The silicone seams at the joint between the floor and the wall will be removed if the floor covering will extend over them.

Sealing

If necessary, all structural joints and boundary points such as floor and wall joints, bushings, columns, and seals of any floor wells, etc. are implemented with a combination of ELAPROOF INDOOR + ELAPROOF BASE FABRIC.

ELAPROOF INDOOR must be mixed before starting the seals. Use a whisk in the mixer that does not take air into the sealant when mixing, eg COLLOMIX KR series mixing paddle.

Apply ELAPROOF INDOOR sealant with a brush and press ELAPROOF BASE FABRIC onto the fresh compound so that all air escapes under the support fabric. Apply another coat of ELAPROOF INDOOR.

Sealing of one running meter (1 rmt) requires approx. 0.15 l of ELAPROOF INDOOR.

If the sealable bushings allow the pre-formed bushing to be threaded over the bushing into a collar, the bushings can be shaped, if necessary, for example, by cutting from N1 or N2 category geo-textiles, unless the ELAPROOF BASE FABRIC is wide enough to carry the penetration. ELAPROOF ROOF series reinforcement fabrics, available in widths of 150 mm, 350 mm and 1000 mm, can also be used for seals.

Coating

Before starting the coating, the ELAPROOF+SAND floor covering must be mixed. Use a mixing paddle in the mixer that does not take air into the sealant when mixing, eg COLLOMIX KR series mixing paddle.

The primed substrate is coated with ELAPROOF+SAND (M1 / EC 1) floor coating. The coating is applied to the substrate with a steel spatula.

ELAPROOF+SAND floor covering is applied to the substrate in two separate applications. The consumption of each application must be at least approx. 2.0 kg / m², in which case the total consumption is approx. 4.0 kg / m². The actual dry film thickness must be min. 2.0 mm.

The drying time between coats of ELAPROOF+SAND depends largely on the conditions at the installation site. At conditions of approx. + 20 °C, 50% RH can be applied a second time approx. 5 h after the first application. Lower temperatures and higher humidity significantly extend the drying time.

The ELAPROOF+SAND floor covering applied twice can be applied after approx. 12 hours in conditions + 20 °C, 50 % RH.

Topcoat

The dried ELAPROOF coating is treated with clear ELACOAT TOPCOAT or tinted ELACOAT TOPCOAT RAL topcoats to facilitate cleaning and maintenance. For monochromatic floors, we recommend topcoating with tinted ELACOAT TOPCOAT RAL topcoat to even out any colour differences in the ELAPROOF+SAND coating. On flaked floors, we recommend flaking with ELAPROOF Art&Deco Colour Chips on wet ELACOAT TOPCOAT RAL topcoat and, after drying, finishing with clear ELACOAT TOPCOAT topcoat.

In the topcoat, the topcoat component A is first mixed for 1 to 2 minutes, then the hardener component B is added to the mixed A component and mixed again for 2-3 minutes. Use, for example, the COLLOMIX KR series mixing paddle for mixing.

The mixture is applied on top of the dried ELAPROOF coating with a short-pile roller (6 – 7 mm) by cross-rolling. The consumption of the topcoat is approx. 110 – 200 g / m² / application, depending on the degree of roughness of the selected ELAPROOF+SAND coating. The topcoat is dry to dry after approx. 16 h at + 20 °C, 50% RH. The full duration of mechanical stress is achieved under the above conditions in about 4 days and the full chemical duration in about 7 days.

NOTE! Some shades of ELACOAT TOPCOAT RAL topcoats may require 2 to 3 coats to achieve sufficient coverage! See a separate table for the coverage of ELACOAT TOPCOAT RAL topcoats.

Structural drawings

All structural drawings related to ElaProof products in DWG and PDF format from the ProdLib-service.

Build Care Oy owns all rights to this coating work method. Designers are free to use this coating work method when creating repair and coating plans!

ALWAYS READ THE PRODUCT DESCRIPTIONS FOR THE PRODUCTS PRESENTED IN THE COATING WORK METHOD BEFORE STARTING THE INSTALLATION!

Updated: 12/2021 | JKo

General

This coating work method is indicative and deals with the coating of a bathroom with plastic carpet flooring with the ELAPROOF+SAND system. The ELAPROOF+SAND floor covering system consists of ELAPROOF PRIMER primer, ELAPROOF+SAND floor covering and ELACOAT TOPCOAT RAL / ELACOAT TOPCOAT topcoat

The coating work method is not a repair plan or a construction plan. The overall design of the coating is always the responsibility of the site-specific designer.

Platform refurbishment

The floor covered with plastic carpet in the bathroom must be less than 10 years old at the coating stage, based on Finnish RIL 107-2012 guidelines. Please check if there are any similar restrictions in the local regulations and follow those! In addition, it must be ascertained whether the PUR protective coating used on a plastic mat, which may impair the adhesive strength of the coatings. If the plastic mat has a PUR coating or cannot be resolved, it is recommended to perform a separate adhesion test with ELAPROOF+SAND floor coating.

The floor covered with a plastic mat is first washed with an acidic (pH 1 – 3) detergent for cleaning the tile surfaces and then with an alkaline (pH 8 – 11) detergent and rinsed with plenty of water. The cleaned floor is allowed to dry for at least 1 day before starting the coating.

Sealing

If necessary, all structural joints and boundary points such as floor and wall joints, bushings, columns, and seals of any floor wells, etc. are implemented with a combination of ELAPROOF INDOOR + ELAPROOF BASE FABRIC.

ELAPROOF INDOOR must be mixed before starting the seals. Use a whisk in the mixer that does not take air into the sealant when mixing, eg COLLOMIX KR series mixing paddle.

Apply ELAPROOF INDOOR sealant with a brush and press ELAPROOF BASE FABRIC onto the fresh compound so that all air escapes under the support fabric. Apply another coat of ELAPROOF INDOOR.

Sealing of one running meter (1 rmt) requires approx. 0.15 l of ELAPROOF INDOOR.

If the sealable bushings allow the pre-formed bushing to be threaded over the bushing into a collar, the bushings can be shaped, if necessary, for example, by cutting from N1 or N2 category geo-textiles, unless the ELAPROOF BASE FABRIC is wide enough to carry the penetration. ELAPROOF ROOF series reinforcement fabrics, available in widths of 150 mm, 350 mm and 1000 mm, can also be used for seals.

Coating

Before starting the coating, the ELAPROOF+SAND floor covering must be mixed. Use a mixing paddle in the mixer that does not take air into the sealant when mixing, eg COLLOMIX KR series mixing paddle.

The primed substrate is coated with ELAPROOF+SAND (M1 / EC 1) floor coating. The coating is applied to the substrate with a steel spatula.

ELAPROOF+SAND floor covering is applied to the substrate in two separate applications. The consumption of each application must be at least approx. 2.0 kg / m², in which case the total consumption is approx. 4.0 kg / m². The actual dry film thickness must be min. 2.0 mm.

The drying time between coats of ELAPROOF+SAND depends largely on the conditions at the installation site. At conditions of approx. + 20 °C, 50% RH can be applied a second time approx. 5 h after the first application. Lower temperatures and higher humidity significantly extend the drying time.

The ELAPROOF+SAND floor covering applied twice can be applied after approx. 12 hours in conditions + 20 °C, 50 % RH.

Topcoat

The dried ELAPROOF coating is treated with clear ELACOAT TOPCOAT or tinted ELACOAT TOPCOAT RAL topcoats to facilitate cleaning and maintenance. For monochromatic floors, we recommend topcoating with tinted ELACOAT TOPCOAT RAL topcoat to even out any colour differences in the ELAPROOF+SAND coating. On flaked floors, we recommend flaking with ELAPROOF Art&Deco Colour Chips on wet ELACOAT TOPCOAT RAL topcoat and, after drying, finishing with clear ELACOAT TOPCOAT topcoat.

In the topcoat, the topcoat component A is first mixed for 1 to 2 minutes, then the hardener component B is added to the mixed A component and mixed again for 2-3 minutes. Use, for example, the COLLOMIX KR series mixing paddle for mixing.

The mixture is applied on top of the dried ELAPROOF coating with a short-pile roller (6 – 7 mm) by cross-rolling. The consumption of the topcoat is approx. 110 – 200 g / m² / application, depending on the degree of roughness of the selected ELAPROOF+SAND coating. The topcoat is dry to dry after approx. 16 h at + 20 °C, 50% RH. The full duration of mechanical stress is achieved under the above conditions in about 4 days and the full chemical duration in about 7 days.

NOTE! Some shades of ELACOAT TOPCOAT RAL topcoats may require 2 to 3 coats to achieve sufficient coverage! See a separate table for the coverage of ELACOAT TOPCOAT RAL topcoats.

Structural drawings

All structural drawings related to ElaProof products in DWG and PDF format from the ProdLib-service.

Build Care Oy owns all rights to this coating work method. Designers are free to use this coating work method when creating repair and coating plans!

ALWAYS READ THE PRODUCT DESCRIPTIONS FOR THE PRODUCTS PRESENTED IN THE COATING WORK METHOD BEFORE STARTING THE INSTALLATION!

Updated: 12/2021 | JKo

General

This coating work method is indicative and deals with the coating of a floor coated with epoxy in the bathroom with the ELAPROOF + SAND system. The ELAPROOF + SAND floor covering system consists of ELAPROOF PRIMER primer, ELAPROOF + SAND floor covering and ELACOAT TOPCOAT RAL / ELACOAT TOPCOAT topcoat.

The coating work method is not a repair plan or a construction plan. The overall design of the coating is always the responsibility of the site-specific designer.

Platform refurbishment

The floor coated with epoxy in the bathroom must be less than 10 years old during the coating phase, based on Finnish RIL 107-2012 guideline. Please check if there are any similar restrictions in the local regulations and follow those.

Any cracks in the epoxy-coated bathroom floor are first treated by soldering them. After the solder resin has dried, the floor coated with epoxy is mechanically sanded.

The sanded epoxy-coated floor is washed with a general-purpose cleaner and rinsed with plenty of water. The cleaned floor is allowed to dry for at least 2 hours before starting the coating.

Sealing

If necessary, the seals of all structural joints and boundary points such as bushings and columns, etc. are implemented with a combination of ELAPROOF INDOOR + ELAPROOF BASE FABRIC.

ELAPROOF INDOOR must be mixed before starting the seals. Use a whisk in the mixer that does not take air into the sealant when mixing, e.g. COLLOMIX KR series mixing paddle.

Apply ELAPROOF INDOOR sealant with a brush and press ELAPROOF BASE FABRIC onto the fresh compound so that all air escapes under the support fabric. Apply another coat of ELAPROOF INDOOR.

If the sealable bushings allow the pre-formed bushing to be threaded over the bushing into a collar, the bushings can be shaped, if necessary, for example, by cutting from N1 or N2 category geo-textiles, unless the ELAPROOF BASE FABRIC is wide enough to carry the penetration. ELAPROOF ROOF series reinforcement fabrics, available in widths of 150 mm, 350 mm, and 1000 mm, can also be used for seals.

Coating

Before starting the coating, the ELAPROOF + SAND floor covering must be mixed. Use a mixing paddle in the mixer that does not take air into the sealant when mixing, eg COLLOMIX KR series mixing paddle.

The primed substrate is coated with ELAPROOF + SAND (M1 / EC 1) floor coating. The coating is applied to the substrate with a steel spatula.

ELAPROOF + SAND floor covering is applied to the substrate in two separate applications. The consumption of each application must be at least approx. 2.0 kg / m² , in which case the total consumption is approx. 4.0 kg / m² . The actual dry film thickness must be min. 2.0 mm.

The drying time between coats of ELAPROOF + SAND depends largely on the conditions at the installation site. At conditions of approx. + 20 °C, 50% RH can be applied a second time approx. 5 h after the first application. Lower temperatures and higher humidity significantly extend the drying time.

The ELAPROOF + SAND floor covering applied twice can be applied after approx. 12 hours in conditions + 20 °C, 50 % RH.

Topcoat

The dried ELAPROOF coating is treated with clear ELACOAT TOPCOAT or tinted ELACOAT TOPCOAT RAL topcoats to facilitate cleaning and maintenance. For monochromatic floors, we recommend topcoating with tinted ELACOAT TOPCOAT RAL topcoat to even out any colour differences in the ELAPROOF + SAND coating. On flaked floors, we recommend flaking with ELAPROOF Art&Deco Colour Chips on wet ELACOAT TOPCOAT RAL topcoat and, after drying, finishing with clear ELACOAT TOPCOAT topcoat.

In the topcoat, the topcoat component A is first mixed for 1 to 2 minutes, then the hardener component B is added to the mixed A component and mixed again for 2-3 minutes. Use, for example, the COLLOMIX KR series mixing paddle for mixing.

The mixture is applied on top of the dried ELAPROOF coating with a short-pile roller (6 – 7 mm) by cross-rolling. The consumption of the topcoat is approx. 110 – 200 g / m² / application, depending on the degree of roughness of the selected ELAPROOF + SAND coating. The topcoat is dry to dry after approx. 16 h at + 20 °C, 50% RH. The full duration of mechanical stress is achieved under the above conditions in about 4 days and the full chemical duration in about 7 days.

NOTE! Some shades of ELACOAT TOPCOAT RAL topcoats may require 2 to 3 coats to achieve sufficient coverage! See a separate table for the coverage of ELACOAT TOPCOAT RAL topcoats.

Build Care Oy owns all rights to this coating work method. Designers are free to use this coating work method when creating repair and coating plans!

ALWAYS READ THE PRODUCT DESCRIPTIONS FOR THE PRODUCTS PRESENTED IN THE COATING WORK METHOD BEFORE STARTING THE INSTALLATION!

Structural drawings

All structural drawings related to ElaProof products in DWG and PDF format from the ProdLib-service.

Updated: 12/2021 | JKo

General

This coating method is indicative and covers the coating of a floor coated with polyurethane in the bathroom with the ELAPROOF + SAND system. The ELAPROOF + SAND floor covering system consists of ELAPROOF PRIMER primer, ELAPROOF + SAND floor covering and ELACOAT TOPCOAT RAL / ELACOAT TOPCOAT topcoat

The coating work method is not a repair plan or a construction plan. The overall design of the coating is always the responsibility of the site-specific designer.

Platform refurbishment

The floor coated with polyurethane compound in the bathroom must be less than 10 years old during the coating phase, based on Finnish RIL 107-2012 guideline. Please check if there are any similar restrictions in the local regulations and follow those.

Any cracks in the bathroom floor coated with polyurethane are first treated by soldering them with a polyurethane compound with similar properties. After the polyurethane solders have dried, the floor coated with polyurethane mass is mechanically sanded.

The sanded polyurethane-coated floor is washed with an all-purpose cleaner and rinsed with plenty of water. The cleaned floor is allowed to dry for at least 2 hours before starting the coating.

Sealing

If necessary, the seals of all structural joints and boundary points such as bushings and columns, etc. are implemented with a combination of ELAPROOF INDOOR + ELAPROOF BASE FABRIC.

ELAPROOF INDOOR must be mixed before starting the seals. Use a whisk in the mixer that does not take air into the sealant when mixing, e.g. COLLOMIX KR series mixing paddle.

Apply ELAPROOF INDOOR sealant with a brush and press ELAPROOF BASE FABRIC onto the fresh compound so that all air escapes under the support fabric. Apply another coat of ELAPROOF INDOOR.

Sealing of one running meter (1 rmt) requires approx. 0.15 l of ELAPROOF INDOOR.

If the sealable bushings allow the pre-formed bushing to be threaded over the bushing into a collar, the bushings can be shaped, if necessary, for example, by cutting from N1 or N2 category geo-textiles, unless the ELAPROOF BASE FABRIC is wide enough to carry the penetration. ELAPROOF ROOF series reinforcement fabrics, available in widths of 150 mm, 350 mm and 1000 mm, can also be used for seals.

Coating

Before starting the coating, the ELAPROOF + SAND floor covering must be mixed. Use a mixing paddle in the mixer that does not take air into the sealant when mixing, eg COLLOMIX KR series mixing paddle.

The primed substrate is coated with ELAPROOF + SAND (M1 / EC 1) floor coating. The coating is applied to the substrate with a steel spatula.

ELAPROOF + SAND floor covering is applied to the substrate in two separate applications. The consumption of each application must be at least approx. 2.0 kg / m², in which case the total consumption is approx. 4.0 kg / m². The actual dry film thickness must be min. 2.0 mm.

The drying time between coats of ELAPROOF + SAND depends largely on the conditions at the installation site. At conditions of approx. + 20 °C, 50% RH can be applied a second time approx. 5 h after the first application. Lower temperatures and higher humidity significantly extend the drying time.

The ELAPROOF + SAND floor covering applied twice can be applied after approx. 12 hours in conditions + 20 °C, 50 % RH.

Topcoat

The dried ELAPROOF coating is treated with clear ELACOAT TOPCOAT or tinted ELACOAT TOPCOAT RAL topcoats to facilitate cleaning and maintenance. For monochromatic floors, we recommend topcoating with tinted ELACOAT TOPCOAT RAL topcoat to even out any colour differences in the ELAPROOF + SAND coating. On flaked floors, we recommend flaking with ELAPROOF Art&Deco Colour Chips on wet ELACOAT TOPCOAT RAL topcoat and, after drying, finishing with clear ELACOAT TOPCOAT topcoat.

In the topcoat, the topcoat component A is first mixed for 1 to 2 minutes, then the hardener component B is added to the mixed A component and mixed again for 2-3 minutes. Use, for example, the COLLOMIX KR series mixing paddle for mixing.

The mixture is applied on top of the dried ELAPROOF coating with a short-pile roller (6 – 7 mm) by cross-rolling. The consumption of the topcoat is approx. 110 – 200 g / m² / application, depending on the degree of roughness of the selected ELAPROOF + SAND coating. The topcoat is dry to dry after approx. 16 h at + 20 °C, 50% RH. The full duration of mechanical stress is achieved under the above conditions in about 4 days and the full chemical duration in about 7 days.

NOTE! Some shades of ELACOAT TOPCOAT RAL topcoats may require 2 to 3 coats to achieve sufficient coverage! See a separate table for the coverage of ELACOAT TOPCOAT RAL topcoats.

Structural drawings

All structural drawings related to ElaProof products in DWG and PDF format from the ProdLib-service.

Build Care Oy owns all rights to this coating work method. Designers are free to use this coating work method when creating repair and coating plans!

ALWAYS READ THE PRODUCT DESCRIPTIONS FOR THE PRODUCTS PRESENTED IN THE COATING WORK METHOD BEFORE STARTING THE INSTALLATION!

Updated: 12/2021 | JKo

Yleistä

Tämä pinnoitustyömenetelmä on ohjeellinen ja käsittelee parvekkeen tai terassin vanerista rakennetun lattian pinnoitusta ELAPROOF + SAND lattiapinnoitteella. Tässä käyttötarkoituksessa lattian pintarakenne koostuu ELAPROOF PRIMER pohjusteesta, ELAPROOF S tiivistysmassasta, ELAPROOF TUKIKANGAS vahvikkeesta, ELAPROOF ROOF vahvikekankaasta, ELAPROOF + SAND lattiapinnoitteesta ja ELACOAT TOPCOAT RAL pintalakasta. Pinnoitustyömenetelmä ei ole korjaussuunnitelma tai rakennesuunnitelma. Pinnoituksen kokonaissuunnittelu on aina kohdekohtaisen suunnittelijan vastuulla.

Pohjustus

Ennen pinnoittamista vanerialusta pohjustetaan ELAPROOF PRIMER pohjusteella ilman vedenlisäystä. Pohjusteen annetaan kuivua kokonaan ennen tiivistysten ja ELAPROOF S pinnoituksen aloittamista. Pohjusteen tarkoitus on sulkea vanerin pinta päälle tulevan pinnoitteen luovuttamalta kosteudelta.

Tiivistykset

Pohjustuksen jälkeen ennen varsinaisen pinnoittamisen aloittamista toteutetaan lattiassa olevien yksityiskohtien silloitukset / tiivistykset.
Vanerialustassa olevat vanerilevyjen saumat silloitetaan ja tiivistetään ELAPROOF S + ELAPROOF TUKIKANGAS yhdistelmällä.
Vanerilattiassa olevat putkien läpiviennit tiivistetään ELAPROOF S + ELAPROOF TUKIKANGAS yhdistelmällä tai ELAPROOF S + ELAPROOF ROOF yhdistelmällä riippuen läpivietävän putken halkaisijasta. ELAPROOF TUKIKANGAS on saatavissa 100 mm ja 200 mm levyisenä ja ELAPROOF ROOF vahvikekangas on saatavilla 350 mm ja 1000 mm levyisenä. Läpivietävän putken ympärille lattialle on jäätävä vähintään 50 mm läpivientivahviketta. Läpivientivahvikkeen tulee nousta kauluksena vähintään 15 mm läpivietävää putkea vasten.
Liitynnät lattiakivoihin toteutetaan noudattaen kaivonvalmistajan ohjeistusta koskien liityntää massapinnoitteilla. Tarvittaessa kaivoon liitynnässä käytetään apuna ELAPROOF ROOF vahvikekankaasta muotoiltua kappaletta.
Ennen tiivistysten aloittamista ELAPROOF S tulee sekoittaa. Käytä sekoittimessa vispilää, joka ei vie ilmaa tiivistysmassaan sekoituksen yhteydessä esim. COLLOMIX KR sarjan lankavispilät.
Levitä ELAPROOF S tiivistysmassaa siveltimellä ja paina ELAPROOF TUKIKANGAS / ELAPROOF ROOF vahvikekangas kiinni tuoreeseen massaan siten, että kaikki ilma poistuu tukikankaan alta. Sivele päälle vielä kerros ELAPROOF S tiivistysmassaa.
Yhden juoksumetrin (1 jm) tiivistys vaatii n. 0,15 l ELAPROOF S tiivistysmassaa.

Ylösnostot

Pinnoitteen nostaminen ylös seinälle jalkalistaksi toteutetaan myös ennen varsinaisen pinnoitustyön aloittamista. Lattian ja seinän liitoskohtaan asennetaan ELAPROOF S + ELAPROOF TUKIKANGAS yhdistelmä noudattaen edellä annettuja asennusohjeita. Asennuksen kuivuttua siten, ettei ELAPROOF S tiivistysmassa enää vaurioidu kosketuksesta toteutetaan pinnoitteen seinälle jalkalistaksi nostettava osuus.
Rajaa teippaamalla ylös nosto haluttuun korkoon. Levitä ELAPROOF + SAND lattiapinnoitetta teräslastalla lattian ja seinänliitoskohdasta rajausteippiin saakka. Tasoita levitetty ELAPROOF + SAND lattiapinnoite riittävään tasaisuuteen ja poista rajausteippi tämän jälkeen.

Vedeneristys

Parvekkeen tai terassin vedeneristyskyvyn varmistaminen toteutetaan ELAPROOF S tiivistysmassalla.
Ennen pinnoittamisen aloittamista ELAPROOF S tiivistysmassa tulee sekoittaa. Käytä sekoittimessa vispilää, joka ei vie ilmaa tiivistysmassaan sekoituksen yhteydessä esim. COLLOMIX KR sarjan lankavispilät.
Levitä ELAPROOF S tiivistysmassa alustaan TKB B2 hammastetulla lastalla sen kokoiselle alueelle, että se voidaan vielä silottaa teräslastalla tasaiseksi kerrokseksi. Silota hammaslastalla levitetty pinnoite sileällä teräslastalla ja jatka työskentelyä tällä tavalla, kunnes koko lattia on käsitelty.
ELAPROOF S tiivistysmassan menekin tulee olla vähintään n. 1,0 -1,5 l/m² , jolloin kuivakalvonpaksuudeksi tulee noin 0,6 – 1,0 mm.

Pinnoitus

ELAPROOF S tiivistysmassan kuivuttua toteutetaan lattian pinnoitus käyttäen keskikarkeaa tai karkeaa ELAPROOF + SAND lattiapinnoitetta. Sekoita ELAPROOF + SAND lattiapinnoite ennen käyttöä.
Levitä tämän jälkeen ELAPROOF + SAND lattiapinnoite sileällä teräslastalla kauttaaltaan lattialle. ELAPROOF + SAND lattiapinnoitteen menekki tässä käyttötarkoituksessa on noin 1 – 2 kg/m² , riippuen valitusta lattiapinnoitteen karkeusasteesta ja alustan tasaisuudesta. Anna lattian kuivua vähintään 12 h ennen pintalakkausta.

Pintalakkaus

Kuivunut ELAPROOF + SAND tuotteella karhennettu lattiapinnoite käsitellään kirkkaalla tai sävytetyllä ELACOAT TOPCOAT RAL pintalakalla puhtaanapidon ja huoltamisen helpottamiseksi.
Pintalakkauksessa sekoitetaan ensin pintalakan komponentti A 1 – 2 minuuttia, tämän jälkeen lisätään sekoitettuun A-komponenttiin kovettaja komponentti B ja sekoitetaan uudelleen 2-3 minuuttia. Käytä sekoitukseen esim. COLLOMIX KR sarjan lankavispilää.
Seos levitetään kuivuneen ELAPROOF+ SAND pinnoitteen päälle lyhytnukkaisella telalla (6 – 7 mm) ristiin telaamalla. Pintalakan menekki on n. 110 – 200 g/m² /levityskerta, riippuen valitun ELAPROOF + SAND pinnoitteen karkeusasteesta. Pintalakka on kävelykuiva n. 16 h kuluttua olosuhteissa + 20 °C, 50 % RH. Täysi mekaanisen rasituksen kesto saavutetaan em. olosuhteissa n. 4 vrk:n päästä sekä täysi kemiallinen kesto n. 7 vrk:n päästä.

Build Care Oy omaa kaikki oikeudet tähän pinnoitustyömenetelmään. Suunnittelijat voivat käyttää tätä pinnoitustyömenetelmää vapaasti korjaus- ja pinnoitussuunnitelmia laatiessaan!

TUTUSTU AINA MYÖS PINNOITUSTYÖMENETELMÄSSÄ ESITETTYJEN TUOTTEIDEN TUOTESELOSTEISIIN ENNEN ASENNUKSEN ALOITTAMISTA!

Rakennepiirrokset

Kaikki ElaProof-tuotteisiin liittyvät rakennepiirrokset löydät DWG- ja PDF-muodossa ProdLib-palvelusta.

Päivitetty: 05/2022 | JK

Yleistä

Tämä pinnoitustyömenetelmä on ohjeellinen ja käsittelee kosteusrasitetun betonilattian pinnoitusta ELAPROOF + SAND järjestelmällä. ELAPROOF + SAND lattianpinnoitusjärjestelmä koostuu tässä tapauksessa ELAPROOF PRIMER pohjusteesta, ELAPROOF INDOOR / ELAPROOF tiivistysmassasta, ELAPROOF + SAND lattiapinnoitteesta ja ELACOAT TOPCOAT RAL / ELACOAT TOPCOAT pintalakasta Pinnoitustyömenetelmä ei ole korjaussuunnitelma tai rakennesuunnitelma. Pinnoituksen kokonaissuunnittelu on aina kohdekohtaisen suunnittelijan vastuulla.

Alustan kunnostus

Riittävä veto- ja puristuslujuus on keskeinen tekijä pinnoitusaineiden toimivuudessa. Betoni- tai tasoitealustan on oltava kestävä ja puristuslujuuden riittävä. Alustamateriaalin vetolujuus tarkastetaan EN 1542 standardin mukaisesti ja vetolujuuden tulee olla >1,5 N/mm² (1,5 MPa).
Puristuslujuus tarkastetaan EN 12504-2 standardin mukaisesti ja puristuslujuuden tulee olla >25 N/mm² (25 MPa).
Alustan tulee olla puhdas, riittävän kuiva ja vapaa kaikista epäpuhtauksista kuten lika, öljy, rasva, heikot pinnoitteet ja pintakäsittelyt.
Tarvittaessa heikot kerrokset poistetaan riittävän tehokkailla mekaanisilla menetelmillä kuten hionta, jyrsintä tai sinkopuhallus. Pinnoituksen osalta paras lopputulos saavutetaan, mikäli se toteutetaan puhtaalle betonipinnalle, jonka karkeus vastaa puuhierrettyä betonipintaa.
Puhdistuksen jälkeen betonilattiassa ilmenevät mahdolliset halkeamat injektoidaan EN 1504-5 standardin täyttävällä injektiohartsilla esim. HYDROPOX EP1.

Alustan paikkaus ja tasoitus

Betonipinnassa olevat mahdolliset kolot täytetään pinnoitusyhdistelmään soveltuvalla täytemassalla ennen pinnoittamista. Jos pinnoitettavassa betonialustassa on rosoisia tai epätasaisia alueita, ne on tasoitettava pinnoitusyhdistelmään soveltuvalla tasoitteella. On huomattava, että epätasaisuudet pyrkivät näkymään pinnoitetussa pinnassa.
Alustan korjaamiseen, oikaisuun ja tasoittamiseen saa käyttää ainoastaan erikoistuotteita, jotka täyttävät yllä mainitut puristus- ja vetolujuusvaatimukset. Edellä mainittujen tuotteiden soveltuvuus nestemäisenä levitettävän pinnoitteen alustaksi on aina varmistettava ko. tuotteen toimittajalta.

Pohjustus

Ennen tiivistämistä puhdistetut ja korjatut betonialustat pohjustetaan ELAPROOF PRIMER pohjusteella laimennettuna 1:2 vedellä (1 osa pohjustetta : 2 osaa vettä). Pohjuste voi olla nihkeää ennen ELAPROOF + SAND pinnoituksen aloittamista mutta pohjusteessa ei saa esiintyä lammikoita.

Tiivistykset

Tarpeen vaatiessa kaikkien rakenteellisten liitos- ja rajakohtien kuten lattian ja seinän liitos, läpiviennit, pilarit sekä mahdollisten lattiakaivojen yms. tiivistykset toteutetaan ELAPROOF INDOOR + ELAPROOF TUKIKANGAS yhdistelmällä.
Ennen tiivistysten aloittamista ELAPROOF INDOOR tulee sekoittaa. Käytä sekoittimessa vispilää, joka ei vie ilmaa tiivistysmassaan sekoituksen yhteydessä esim. COLLOMIX KR sarjan lankavispilät.
Levitä ELAPROOF INDOOR tiivistysmassaa siveltimellä ja paina ELAPROOF TUKIKANGAS kiinni tuoreeseen massaan siten, että kaikki ilma poistuu tukikankaan alta. Sivele päälle vielä kerros ELAPROOF INDOOR massaa.
Yhden juoksumetrin (1 jm) tiivistys vaatii n. 0,15 l ELAPROOF INDOOR-massaa.
Mikäli tiivistettävät läpiviennit mahdollistavat valmiiksi muotoillun läpivientikappaleen pujottamisen läpiviennin päältä kaulukseksi, voidaan läpivientikappaleet muotoilla tarvittaessa esim. N1 tai N2 luokan geo-tekstiilistä leikkaamalla, ellei ELAPROOF TUKIKANGAS ole riittävän leveä läpiviennin toteuttamiseen. Tiivistyksissä voidaan käyttää myös ELAPROOF ROOF sarjan vahvikekankaita, jotka ovat saatavilla leveyksissä 150mm, 350 mm ja 1000mm.
Mahdolliset lattiakaivoon liittymiset toteutetaan myös muotoilemalla lattiakaivon läpivientikappale N1 tai N2 luokan geo-tekstiilistä tai ELAPROOF ROOF sarjan vahvikekankaasta leikkaamalla. Läpivientikappale asennetaan käyttämällä tai ELAPROOF INDOOR massaa. Levitä ELAPROOF INDOOR tiivistysmassaa siveltimellä ja paina läpivientikappale kiinni tuoreeseen massaan siten, että kaikki ilma poistuu tukikankaan alta. Sivele päälle vielä kerros ELAPROOF INDOOR massaa. Läpiviennin kuivuttua leikkaa läpivientiin sopivan kokoinen reikä ja paina lattiakaivon kiristysrengas paikoilleen ennen ELAPROOF + SAND lattiapinnoituksen aloittamista.
Lattiapinnat käsitellään yksityiskohtien tiivistämisen jälkeen kauttaaltaan ELAPROOF INDOOR / ELAPROOF tiivistysmassalla vedeneristyskyvyn varmistamiseksi. Tiivistysmassa levitetään alustaan siveltimellä, telalla tai lastalla, riippuen alustan muodoista yms. Tietyissä tapauksissa myös pinnoitteen ruiskuttaminen on mahdollista, kts. erillinen ruiskutusohje.
ELAPROOF pinnoitteet levitetään alustaan kahdella erillisellä levityskerralla. Kunkin levityskerran märkäkalvopaksuuden tulee olla min. 0,5 mm, jolloin kokonaismenekiksi muodostuu n. 1,2 l/m² . Toteutuneen kuivakalvonpaksuuden tulee olla min. 0,6 mm.
ELAPROOF pinnoituskertojen välinen kuivumisaika sekä sateen kestävyys riippuvat suuresti alustan imukykyisyydestä sekä asennuspaikalla vallitsevista olosuhteista. Olosuhteiden ollessa n. + 20 °C, 50 % RH voidaan toinen levityskerta suorittaa n. 5 h kuluttua ensimmäisestä levityksestä. Matalampi lämpötila ja korkeampi ilmankosteus pidentävät merkittävästi kuivumisaikaa. Sateen kestävyys saavutetaan yleensä yllä mainituissa olosuhteissa n. 3 h kuluttua.

Pinnoitus

Ennen pinnoittamisen aloittamista ELAPROOF + SAND lattiapinnoite tulee sekoittaa. Käytä sekoittimessa vispilää, joka ei vie ilmaa tiivistysmassaan sekoituksen yhteydessä esim. COLLOMIX KR sarjan lankavispilät.
Pohjustettu alusta pinnoitetaan ELAPROOF + SAND (M1 / EC 1) lattiapinnoitteella. Pinnoite levitetään alustaan teräslastalla.
ELAPROOF + SAND lattiapinnoite levitetään alustaan kahdella erillisellä levityskerralla. Kunkin levityskerran menekin tulee olla vähintään n. 1,0 kg/m² jolloin kokonaismenekiksi muodostuu vähintään 2,0 kg/m² . Toteutuneen kuivakalvonpaksuuden tulee olla min. 1,0 mm. ELAPROOF + SAND pinnoituskertojen välinen kuivumisaika riippuvat suuresti asennuspaikalla vallitsevista olosuhteista. Olosuhteiden ollessa n. + 20 °C, 50 % RH voidaan toinen levityskerta suorittaa n. 5 h kuluttua ensimmäisestä levityksestä. Matalampi lämpötila ja korkeampi ilmankosteus pidentävät merkittävästi kuivumisaikaa. Kahteen kertaan levitetty ELAPROOF + SAND lattiapinnoitus on jatkokäsittelykelpoinen n. 12 h kuluttua olosuhteissa + 20 °C, 50 % RH.

Pintalakkaus

Kuivunut ELAPROOF pinnoite käsitellään kirkkaalla ELACOAT TOPCOAT tai sävytetyillä ELACOAT TOPCOAT RAL pintalakoilla puhtaanapidon ja huoltamisen helpottamiseksi. Yksivärisiksi jäävissä lattioissa suosittelemme pintalakkausta sävytetyllä ELACOAT TOPCOAT RAL pintalakalla mahdollisten ELAPROOF + SAND pinnoitteen värierojen tasaamiseksi. Hiutaloiduissa lattioissa suosittelemme tekemään hiutaloinnin ELAPROOF PVA värihiutaleilla märkään ELACOAT TOPCOAT RAL pintalakkaan ja kuivumisen jälkeen suorittamaan viimeistelylakkauksen kirkkaalla ELACOAT TOPCOAT pintalakalla.
Pintalakkauksessa sekoitetaan ensin pintalakan komponentti A 1 – 2 minuuttia, tämän jälkeen lisätään sekoitettuun A-komponenttiin kovettaja komponentti B ja sekoitetaan uudelleen 2-3 minuuttia. Käytä sekoitukseen esim. COLLOMIX KR sarjan lankavispilää.
Seos levitetään kuivuneen ELAPROOF pinnoitteen päälle lyhytnukkaisella telalla (6 – 7 mm) ristiin telaamalla. Pintalakan menekki on n. 110 – 200 g/m² /levityskerta, riippuen valitun ELAPROOF + SAND pinnoitteen karkeusasteesta. Pintalakka on kävelykuiva n. 16 h kuluttua olosuhteissa + 20 °C, 50 % RH. Täysi mekaanisen rasituksen kesto saavutetaan em. olosuhteissa n. 4 vrk:n päästä sekä täysi kemiallinen kesto n. 7 vrk:n päästä.
HUOM! Jotkut ELAPROOF TOPCOAT RAL pintalakkojen värisävyt saattavat vaatia 2 – 3 käsittelykertaa riittävän peittoasteen saavuttamiseksi! Katso erillinen taulukko ELACOAT TOPCOAT RAL pintalakkojen peittävyydestä.

Build Care Oy omaa kaikki oikeudet tähän pinnoitustyömenetelmään. Suunnittelijat voivat käyttää tätä pinnoitustyömenetelmää vapaasti korjaus- ja pinnoitussuunnitelmia laatiessaan!

TUTUSTU AINA MYÖS PINNOITUSTYÖMENETELMÄSSÄ ESITETTYJEN TUOTTEIDEN TUOTESELOSTEISIIN ENNEN ASENNUKSEN ALOITTAMISTA!

Rakennepiirrokset

Kaikki ElaProof-tuotteisiin liittyvät rakennepiirrokset löydät DWG- ja PDF-muodossa ProdLib-palvelusta.

Päivitetty: 05/2022 | JK

General

This coating work method is indicative and deals with the coating of a chipboard- / OSB wall with the ELAPROOF + SAND system. The ELAPROOF + SAND wall covering system consists of ELAPROOF PRIMER primer, ELAPROOF + SAND wall covering and ELACOAT TOPCOAT RAL / ELACOAT TOPCOAT topcoat

The coating work method is not a repair plan or a construction plan. The overall design of the coating is always the responsibility of the site-specific designer.

Platform refurbishment

In areas to be renovated, all possible moisture-sensitive adhesive residues must be removed from the chipboard- / OSB floor. Any loose floor screeds must also be removed in their entirety.

Any gaps between the boards, screw holes and cracks in the board surfaces must be filled / levelled with a wall level suitable for chipboard- / OSB surfaces. A wall level suitable for chipboard surfaces should also be used for possible over-levelling. When using screeds, also check with the floor screed manufacturer for a suitable primer.

Primer

Prior to coating, cleaned and repaired chipboard- / OSB substrates are primed with ELAPROOF PRIMER without the addition of water. Allow the primer to dry completely before applying ELAPROOF + SAND. The purpose of the primer is to seal the surface of the chipboard from the moisture released by the incoming coating.

Chipboard walls painted with a good quality primer do not need to be primed separately. Old primer or topcoat coats can be sanded mechanically or treated with suitable washing liquid to ensure adhesion of ELAPROOF + SAND Wall covering. In these cases, it is also recommended to carry out a separate adhesion test before treating larger areas, to ensure that the adhesion between ELAPROOF + SAND Wall covering and the paint and at the same time sufficient adhesion of the original paint to the substrate after the coating is applied.

Coating

Before starting the coating, the ELAPROOF + SAND Wall covering must be mixed. Use a mixing paddle in the mixer that does not take air into the sealant when mixing, eg COLLOMIX KR series mixing paddle.

The primed substrate is coated with ELAPROOF + SAND (M1 / EC 1) wall coating. The coating is applied to the substrate with a steel spatula.

ELAPROOF + SAND Wall covering is applied to the substrate in two separate applications. The consumption of each application must be at least approx. 1.0 kg / m², in which case the total consumption is at least 2.0 kg / m². The actual dry film thickness must be min. 1.0 mm.

The drying time between coats of ELAPROOF + SAND depends largely on the conditions at the installation site. At conditions of approx. + 20 °C, 50% RH can be applied a second time approx. 5 h after the first application. Lower temperatures and higher humidity significantly extend the drying time.

The ELAPROOF + SAND Wall covering applied twice can be applied after approx. 12 hours in conditions + 20 °C, 50 % RH.

Topcoat

The dried ELAPROOF coating is treated with clear ELACOAT TOPCOAT or tinted ELACOAT TOPCOAT RAL topcoats to facilitate cleaning and maintenance. For monochromatic floors, we recommend top coating with tinted ELACOAT TOPCOAT RAL topcoat to even out any colour differences in the ELAPROOF + SAND coating. On flaked floors, we recommend flaking with ELAPROOF PVA paint flakes on wet ELACOAT TOPCOAT RAL topcoat and, after drying, finishing with clear ELACOAT TOPCOAT topcoat.

In the topcoat, the topcoat component A is first mixed for 1 to 2 minutes, then the hardener component B is added to the mixed A component and mixed again for 2-3 minutes. Use, for example, the COLLOMIX KR series mixing paddle for mixing.

The mixture is applied on top of the dried ELAPROOF coating with a short-pile roller (6 – 7 mm) by cross-rolling. The consumption of the topcoat is approx. 110 – 200 g / m2 / application, depending on the degree of roughness of the selected ELAPROOF + SAND coating. The topcoat is dry to dry after approx. 16 h at + 20 °C, 50% RH. The full duration of mechanical stress is achieved under the above conditions in about 4 days and the full chemical duration in about 7 days.

NOTE! Some shades of ELACOAT TOPCOAT RAL topcoats may require 2 to 3 coats to achieve sufficient coverage! See a separate table for the coverage of ELACOAT TOPCOAT RAL topcoats.

Build Care Oy owns all rights to this coating work method. Designers are free to use this coating work method when creating repair and coating plans!

ALWAYS READ THE PRODUCT DESCRIPTIONS FOR THE PRODUCTS PRESENTED IN THE COATING WORK METHOD BEFORE STARTING THE INSTALLATION!

Structural drawings

All structural drawings related to ElaProof products in DWG and PDF format from the ProdLib-service.

Updated: 01/2022 | JKo

General

This coating work method is indicative and deals with the coating of a gypsum board wall with the ELAPROOF + SAND system. The ELAPROOF + SAND wall covering system consists of ELAPROOF PRIMER primer, ELAPROOF + SAND wall covering and ELACOAT TOPCOAT RAL / ELACOAT TOPCOAT topcoat

The coating work method is not a repair plan or a construction plan. The overall design of the coating is always the responsibility of the site-specific designer.

Platform refurbishment

In areas to be renovated, all possible moisture-sensitive adhesive residues must be removed from the gypsum board wall. Any loose floor screeds must also be removed in their entirety.

Any gaps between the boards, screw holes and cracks in the board surfaces must be filled / levelled with a floor level suitable for gypsum board surfaces. A floor level suitable for chipboard surfaces should also be used for possible over-levelling. When using screeds, also check with the floor screed manufacturer for a suitable primer.

Primer

Prior to coating, cleaned and repaired Gypsum board substrates are primed with ELAPROOF PRIMER without the addition of water. Allow the primer to dry completely before applying ELAPROOF + SAND. The purpose of the primer is to seal the surface of the gypsum board from the moisture released by the incoming coating.

Gypsum board walls painted with a good quality primer do not need to be primed separately. Old primer or topcoat coats can be sanded mechanically or treated with suitable washing liquid to ensure adhesion of ELAPROOF + SAND Wall covering. In these cases, it is also recommended to carry out a separate adhesion test before treating larger areas, to ensure that the adhesion between ELAPROOF + SAND Wall covering and the paint and at the same time sufficient adhesion of the original paint to the substrate after the coating is applied.

Coating

Before starting the coating, the ELAPROOF + SAND Wall covering must be mixed. Use a mixing paddle in the mixer that does not take air into the sealant when mixing, eg COLLOMIX KR series mixing paddle.

The primed substrate is coated with ELAPROOF + SAND (M1 / EC 1) wall coating. The coating is applied to the substrate with a steel spatula.

ELAPROOF + SAND Wall covering is applied to the substrate in two separate applications. The consumption of each application must be at least approx. 1.0 kg / m², in which case the total consumption is at least 2.0 kg / m². The actual dry film thickness must be min. 1.0 mm.

The drying time between coats of ELAPROOF + SAND depends largely on the conditions at the installation site. At conditions of approx. + 20 °C, 50% RH can be applied a second time approx. 5 h after the first application. Lower temperatures and higher humidity significantly extend the drying time.

The ELAPROOF + SAND Wall covering applied twice can be applied after approx. 12 hours in conditions + 20 °C, 50 % RH.

Topcoat

The dried ELAPROOF coating is treated with clear ELACOAT TOPCOAT or tinted ELACOAT TOPCOAT RAL topcoats to facilitate cleaning and maintenance. For monochromatic floors, we recommend topcoating with tinted ELACOAT TOPCOAT RAL topcoat to even out any color differences in the ELAPROOF + SAND coating. On flaked floors, we recommend flaking with ELAPROOF Art&Deco Colour Chips on wet ELACOAT TOPCOAT RAL topcoat and, after drying, finishing with clear ELACOAT TOPCOAT topcoat.

In the topcoat, the topcoat component A is first mixed for 1 to 2 minutes, then the hardener component B is added to the mixed A component and mixed again for 2-3 minutes. Use, for example, the COLLOMIX KR series mixing paddle for mixing.

The mixture is applied on top of the dried ELAPROOF coating with a short-pile roller (6 – 7 mm) by cross-rolling. The consumption of the topcoat is approx. 110 – 200 g / m² / application, depending on the degree of roughness of the selected ELAPROOF + SAND coating. The topcoat is dry to dry after approx. 16 h at + 20 °C, 50% RH. The full duration of mechanical stress is achieved under the above conditions in about 4 days and the full chemical duration in about 7 days.

NOTE! Some shades of ELACOAT TOPCOAT RAL topcoats may require 2 to 3 coats to achieve sufficient coverage! See a separate table for the coverage of ELACOAT TOPCOAT RAL topcoats.

Build Care Oy owns all rights to this coating work method. Designers are free to use this coating work method when creating repair and coating plans!

ALWAYS READ THE PRODUCT DESCRIPTIONS FOR THE PRODUCTS PRESENTED IN THE COATING WORK METHOD BEFORE STARTING THE INSTALLATION!

Structural drawings

All structural drawings related to ElaProof products in DWG and PDF format from the ProdLib-service.

Updated: 01/2022 | JKo